MyCalCute
Install
Science

How to turn a horizontal tank depth reading into liters

Convert liquid depth to volume in a horizontal cylinder and check the result at quarter depth, half depth, and full capacity.

Method

A dipstick in a horizontal cylindrical tank measures the height of the liquid above the inside bottom. Equal increases in height do not add equal amounts of liquid. The tank is narrow near the bottom and top, and widest through its center. Convert the reading to the area of the filled cross-section before multiplying by the length.

Use the inside radius r, the straight internal length L, and the depth h measured vertically from the inside bottom. Use one length unit throughout and calculate the inverse cosine in radians. With dimensions in meters, the volume comes out in cubic meters. Multiply by 1,000 for liters.

Volume at five dipstick readingsVolume at five dipstick readingsEmpty0 LQuarter depth307.1 LHalf depth785.4 LThree-quarter depth1,263.7 LFull1,570.8 L
Volume at five dipstick readingsTake a tank with a 1 m inside diameter and a 2 m straight length. At 0.25 m of liquid depth, the filled cross-section is about 0.1535 m². That gives about 307.1 L out of a full 1,570.8 L. The dipstick reads 25% of the diameter, but the tank holds only about 19.6% of its capacity.Volume at five dipstickreadingsEmpty0 LQuarter depth307.1 LHalf depth785.4 LThree-quarterdepth1,263.7 LFull1,570.8 LMyCalCute.com
Volume at five dipstick readings

Take a tank with a 1 m inside diameter and a 2 m straight length. At 0.25 m of liquid depth, the filled cross-section is about 0.1535 m². That gives about 307.1 L out of a full 1,570.8 L. The dipstick reads 25% of the diameter, but the tank holds only about 19.6% of its capacity.

View data
Empty
0 L
Quarter depth
307.1 L
Half depth
785.4 L
Three-quarter depth
1263.7 L
Full
1570.8 L

Worked example

Take a tank with a 1 m inside diameter and a 2 m straight length. At 0.25 m of liquid depth, the filled cross-section is about 0.1535 m². That gives about 307.1 L out of a full 1,570.8 L. The dipstick reads 25% of the diameter, but the tank holds only about 19.6% of its capacity.

At 0.50 m, the liquid splits the circular end into two equal areas, giving about 785.4 L. At 0.75 m, the empty cap has the same volume as the quarter-depth fill. Adding the volumes at 0.25 m and 0.75 m should therefore give the full capacity, within rounding.

<code data-no-translate>A = r² arccos((r − h)/r) − (r − h)√(2rh − h²)

<code data-no-translate>V = A × L

From dipstick to litersFrom dipstick to liters1Measure internaldimensionsRadius, length, andvertical liquiddepth2Find the filled areaCircular segmentarea in squaremeters3Multiply by lengthand convertCubic meters × 1,000gives liters
From dipstick to litersThis model assumes level installation, a circular bore, and flat ends. Dished ends, slope, and internal displacement change the depth-to-volume relationship. For inventory, custody transfer, or safety limits, use a calibration table made for the installed tank. Concept diagram; not to scale.From dipstick to liters1Measure internal dimensionsRadius, length, and verticalliquid depth2Find the filled areaCircular segment area in squaremeters3Multiply by length and convertCubic meters × 1,000 giveslitersMyCalCute.com
From dipstick to liters

This model assumes level installation, a circular bore, and flat ends. Dished ends, slope, and internal displacement change the depth-to-volume relationship. For inventory, custody transfer, or safety limits, use a calibration table made for the installed tank.

View data
Measure internal dimensions
Radius, length, and vertical liquid depth
Find the filled area
Circular segment area in square meters
Multiply by length and convert
Cubic meters × 1,000 gives liters

Checks and limits

This model assumes level installation, a circular bore, and flat ends. Dished ends, slope, and internal displacement change the depth-to-volume relationship. For inventory, custody transfer, or safety limits, use a calibration table made for the installed tank.

Related calculators

Sources · OpenStax geometry reference