MyCalCute
Install
Science

Plan a sheet cutting grid with kerf and rotation

Compare two rectangular cut layouts with blade width, check a 1,220 × 2,440 mm sheet, and account for margins before cutting.

Method

A sheet can have enough total area for a batch of parts and still be too narrow for another row. A cutting grid counts the whole parts that fit across each direction. Kerf is the strip of material removed by the blade. In this model it separates adjacent finished parts, with edge trims reserved separately.

Measure the usable width and length after trimming any damaged or uneven edges. To fit n parts along an edge, allow n part widths and n − 1 kerfs. Add one kerf to the usable dimension before dividing by the part width plus kerf, then round down. Repeat along the other edge and multiply the counts.

Yield in the two orientationsYield in the two orientations320 mm across15450 mm across14
Yield in the two orientationsOn a usable 1,220 × 2,440 mm sheet, test parts measuring 320 × 450 mm with a 3 mm kerf. The first direction fits 3 parts across and 5 along, giving 15 parts. The parts and separating kerfs occupy 966 mm across and 2,262 mm along.Yield in the two orientations320 mm across15450 mm across14MyCalCute.com
Yield in the two orientations

On a usable 1,220 × 2,440 mm sheet, test parts measuring 320 × 450 mm with a 3 mm kerf. The first direction fits 3 parts across and 5 along, giving 15 parts. The parts and separating kerfs occupy 966 mm across and 2,262 mm along.

View data
320 mm across
15
450 mm across
14

Worked example

On a usable 1,220 × 2,440 mm sheet, test parts measuring 320 × 450 mm with a 3 mm kerf. The first direction fits 3 parts across and 5 along, giving 15 parts. The parts and separating kerfs occupy 966 mm across and 2,262 mm along.

Rotate every part 90 degrees for a second test. Now 2 parts fit across and 7 fit along, for 14 parts. The first uniform orientation yields one extra part. Keep the orientation fixed if grain, a surface pattern, or a marked edge controls how the pieces will be used.

<code data-no-translate>parts across = floor((usable length + kerf)/(part length + kerf))

<code data-no-translate>parts per sheet = parts across × parts along

Check the layout before cuttingCheck the layout before cutting1Measure usable areaSet aside trim andclamp margins2Count rows andcolumnsAllow one kerfbetween neighbors3Check the blade andgrainTest a scrap andmark the retainededge
Check the layout before cuttingA uniform grid provides a repeatable layout, but mixed orientations or nesting may fit more parts. The estimate also leaves edge cleanup, hold-down allowances, and cut sequence to the operator. Mark the retained side of each cut and confirm the actual kerf on a scrap before cutting the sheet. Concept diagram; not to scale.Check the layout beforecutting1Measure usable areaSet aside trim and clampmargins2Count rows and columnsAllow one kerf betweenneighbors3Check the blade and grainTest a scrap and mark theretained edgeMyCalCute.com
Check the layout before cutting

A uniform grid provides a repeatable layout, but mixed orientations or nesting may fit more parts. The estimate also leaves edge cleanup, hold-down allowances, and cut sequence to the operator. Mark the retained side of each cut and confirm the actual kerf on a scrap before cutting the sheet.

View data
Measure usable area
Set aside trim and clamp margins
Count rows and columns
Allow one kerf between neighbors
Check the blade and grain
Test a scrap and mark the retained edge

Checks and limits

A uniform grid provides a repeatable layout, but mixed orientations or nesting may fit more parts. The estimate also leaves edge cleanup, hold-down allowances, and cut sequence to the operator. Mark the retained side of each cut and confirm the actual kerf on a scrap before cutting the sheet.

Related calculators

Sources · OpenStax measurement and geometry